is a small, palm-sized In-Circuit Debugger for the TMS320C2000 family
of DSPs from Texas Instruments. It is equipped with a USB 2.0
port (USB 1.1 compatible) that runs in the High-Speed mode at 480
Mb/sec.
JTAGjet-C2000
supports the
following C2000
DSP devices:
•
TMS320C24x
•
TMS320C28xx
•
TMS320C280xx
•
TMS320C2833x
•
TMS320F24x
•
TMS320F28xx
•
TMS320LC240x
•
TMS320LF240x
•
TMS320R28xx
•
Supports TI TMS320C24xx
and F28xx DSPs.
•
USB 2.0 high-speed port (480 Mbps) provides faster
downloads.
•
Programmable
JTAG clock from 1KHz to 30 MHz.
•
Supports all on-chip breakpoints and RTDX
•
Powered by the USB port –
no external power adapters needed.
•
3 LEDs provide status of target power, JTAG activity,
PC host activity and emulator power.
JTAGjet-C2000 is fully compatible with Code Composer Studio 3.1
or newer. It installs directly into the Code Composer Studio directories
and becomes visible as JTAGjet Emulator in the CCS Setup utility and
preconfigured with many C2000 targets. Setting up to work with JTAGjet
is just as easy as setting up a TI emulator – just drag and drop the
preconfigured target and emulator configuration and start CCS.
For custom made boards with more than one device on the JTAG chain,
JTAGjet can detect all devices on the chain which is necessary in
to configure the CCS debugger.
Detects and graphically shows all devices on
the JTAG chain.
•
Graphically monitors all pins
on the JTAG header.
•
Windows Vista, XP, 2000, NT, ME, 98 & 95 compatible.
JTAGjet-TMS supports variable JTAG clock. It defaults to 10 MHz, but
may be set as low as 1 kHz (for slow FPGA prototypes or power saving
devices) to 30 MHz to provide faster application downloads and quicker
Flash programming.
JTAGjet-TMS comes with a detachable, active JTAG probe to better accommodate
long scan chains and various JTAG pinout standards and low voltages.
The standard probe comes with 14-pin XDS510 & XDS560 compatible header
and supports targets from 3V to 5V. A low voltage probe is available
as option for targets between 1.4V and 4.5V.
is a small, palm-sized In-Circuit Debugger for the TMS320C2000 family
of DSPs from Texas Instruments. It is equipped with a USB 2.0
port (USB 1.1 compatible) that runs in the High-Speed mode at 480
Mb/sec.
JTAGjet-C2000 is fully compatible with Code Composer Studio 3.1
or newer. It installs directly into the Code Composer Studio directories
and becomes visible as JTAGjet Emulator in the CCS Setup utility and
preconfigured with many C2000 targets. Setting up to work with JTAGjet
is just as easy as setting up a TI emulator – just drag and drop the
preconfigured target and emulator configuration and start CCS.
For custom made boards with more than one device on the JTAG chain,
JTAGjet can detect all devices on the chain which is necessary in
to configure the CCS debugger.
JTAGjet-TMS supports variable JTAG clock. It defaults to 10 MHz, but
may be set as low as 1 kHz (for slow FPGA prototypes or power saving
devices) to 30 MHz to provide faster application downloads and quicker
Flash programming.
JTAGjet-TMS comes with a detachable, active JTAG probe to better accommodate
long scan chains and various JTAG pinout standards and low voltages.
The standard probe comes with 14-pin XDS510 & XDS560 compatible header
and supports targets from 3V to 5V. A low voltage probe is available
as option for targets between 1.4V and 4.5V.